Installing Cover Guards for MPR Clinical Recliners
Assembly, Installation and Operating Instructions
Kit # 1102816 for Model Nos. 6905A, 6907A, 6908A
SAVE THESE INSTRUCTIONS
NOTE: Check all parts for shipping damage, in case of damage, DO NOT use. Contact Carrier/Invacare
for further instructions.
SAFETY SUMMARY
To ensure the safe and proper installation and use of footrest and scissor mechanism guards,
these instructions MUST be followed:
GENERAL WARNING
DO NOT install this equipment without first reading and understanding this
instruction sheet and the Invacare Mobile Recliners Manual, part number
54000M107. If you are unable to understand the warnings, cautions and
instructions, contact a healthcare professional, dealer or technical personnel
if applicable, before attempting to install this equipment - otherwise, injury
or damage may occur.
INSTALLATION WARNING
After ANY adjustments, repair, or service and BEFORE use, make sure that all
attaching hardware is tightened securely.
Description
Quantity
Footrest Cover
Mechanism Cover
Tie Wrap
2
2
2
INSTALLING FOOTREST GUARD AND SCISSOR
MECHANISM GUARD
FOOTREST GUARD (FIGURE 1)
NOTE: Right and left sides are determined from the user’s seated position.
1. Engage wheel locks.
2. Extend the footrest of the recliner.
3. Carefully tip the recliner onto the right side. Be sure there are no obstructions on or
around the floor before doing this.
4. Remove mounting bolt from support tube as shown in DETAIL “A” in FIGURE 1.
5. Install footrest guard around the footrest frame as shown in DETAIL “A” in FIGURE 1.
NOTE: Footrest guard needs to be folded in two (2) locations so it will wrap entirely around the upper
frame. Refer to the scored lines on the guard to determine where the folds should be.
6. Once folded, align the two (2) mounting holes of the footrest guard with the mounting
hole in the upper frame as shown in DETAIL “A” in FIGURE 1.
7. Using the mounting bolt, secure the footrest guard and upper frame to the support tube
as shown in DETAIL “A” in FIGURE 1.
1
DETAIL “A” - MODEL 6905A
MANUFACTURED BEFORE
04/01/2002
DETAIL “B” - MODEL 6905A
MANUFACTURED AFTER
04/01/2002
Recliner Frame
Bolts
Rivets
Recliner Frame
Bolts
Rivets
Bolts
Rivets
NOTE: Side panel not shown to show rivet
locations.
DETAIL “C” - REMOVING SIDE COVER MODELS 6907A AND 6908A
Bolts
FIGURE 2 - INSTALLING THE SCISSOR MECHANISM GUARD
4. Remove four (4) existing bolts A, B, C and D from side frame as shown in
FIGURE 3.
5. Position scissor mechanism guard against the side frame with the folded edge down.
Refer to FIGURE 3.
6. Align holes of scissor mechanism guard with holes on side frame.
7. Secure scissor mechanism guard to side frame with existing bolts A, B, C, and D.
8. Perform one (1) of the following:
A. FOR MODEL 6905A BUILT BEFORE 04/01/2002 - Install new side panel
with kit no. 1109705 and using instruction sheet no. 1109704.
B. FOR MODEL 6905A BUILT AFTER 04/01/2002 - Secure the side cover to
the recliner frame with the eleven (11) bolts. Refer to DETAIL “B” in FIGURE 2.
C. FOR MODELS 6907A, 6908A - Secure the side cover to the recliner frame
with the four (4) bolts. Refer to DETAIL "C" in FIGURE 2.
3
9. Place chair in the upright position.
10. Close the footrest.
NOTE: If binding or pinching of footrest guard occurs, call Invacare at the number listed below.
11. Carefully tip recliner onto the left side. Be sure there are no obstructions on or around the
floor before doing this.
12. Repeat STEPS 3-11 to install remaining scissor mechanism guard.
SIDE VIEW
REAR OF
CHAIR
FRONT OF
CHAIR
Seat Cushion
Side Frame
Footrest
DO NOT
remove this bolt
Scissor Mechanism Guard
Bolt A Bolt B
Bolt C Bolt D
NOTE: Some detail removed for clarity.
FIGURE 3 - INSTALLING THE SCISSOR MECHANISM GUARD
Invacare Corporation
USA
One Invacare Way
Elyria, Ohio USA
44036-2125
Invacare is a registered trademark of
Invacare Corporation.
Yes, you can. is a trademark of Invacare
Corporation.
800-333-6900
© 2002 Invacare Corporation
Part No. 1109697 Rev B - 7/02
|